![]() This can be used to turn on accessories such as lights, CCTV camera, or notify a guard. KEYPAD ACTIVE OUTPUT The Command and Control Series Door-Gards can be programmed to energize a voltage output whenever a key is touched. This can be turned off through programming. KEYPRESS FEEDBACK / AUDIBLE KEYPRESS The Command and Control Series Door-Gards will acknowledge a keypress by momentarily illuminating the yellow LED like on the indoor(i), or momentarily sounding the sounder like in the sealed environmental(se) style. This feature is especially useful when controlling an electric locking device. The main relay (if selected) will energize for the same time period as the Master Code. Upon a momentary closure, the selected outputs will energize for their programmed time. REMOTE TRIGGERING INPUT (REX) This normally open loop that by default operates the Main Relay upon activation and can be programmed to trigger any combination of outputs. The Ruggedized(r), Sealed Environmental(se), Multipad and Xtreme style provide these outputs in the form of 1 Amp Form-C relays, all other styles have negative voltage outputs with a 50mA sink. AUXILIARY OUTPUTS Auxiliary outputs can be individually timed from 1 to 90 seconds or act as a toggle switch, and may be triggered individually or in combination-by code. ![]() MAIN RELAY This is an 8 Amp (10 Amp surge) Form-C relay which can be toggled or timed from 1 to 90 seconds-by code. The Master Code is always assigned to user location one (1). Codes may be from 1-6 digits in length and digits may be repeated. CODES The Door-Gard Command and Control keypads allow up to 120 individual user codes to be valid. LED or Sounder guidance makes programming easy, and changing codes a matter of seconds for an authorized user. PROGRAMMING All programming is accomplished entirely from the front of the keypad. FEATURES: 4 INDEPENDENT OUTPUTS 4 INDEPENDENT TIMERS ALL OUTPUTS ASSIGNABLE BY CODE ON BOARD 8 AMP FORM C RELAY 120 USERS REMOTE TRIGGERING INPUT KEYPAD PROGRAMMABLE MEMORY Non-volatile EEPROM memory means your codes and instructions will be there whether you remove power for 5 minutes or 5 years. Door-Gards accept power from a 12 or 24V AC/DC Supply. Designed for individual control of up to four devices, Door-Gard Command and Control Series keypads are the perfect choice for controlling electric locking devices, security systems, automatic operators or machinery. This warranty shall expire two years after shipping date for DOOR-GARD keypads.Įxcept as stated above, IEI makes no warranties, either express or implied, as to any matter whatsoever, including, without limitation to, the condition of its products, their merchantability, or fitness for any particular purpose.1 FEATURES AND PROGRAMMING GUIDE COMMANDANDCONTROLSERIES DOOR-GARD COMMAND AND CONTROL SERIESkeypads offer field proven reliability and cost effective solutions anywhere limited control or access is desired. IEI will not be liable to the purchaser or anyone else for incidental or consequential damages arising from any defect in, or malfunction of, its products. IEI’s sole liability is limited to the repair or (at IEI’s option) the replacement of the defective product or part when sent to IEI’s facility (freight and insurance charges prepaid), after first obtaining IEI’s Return Merchandise Authorization. IEI does not assume any responsibility for damage or injury to person or property due to improper care, storage, handling, abuse, misuse, normal wear and tear, or an act of God. (IEI) warrants its products to be free from defects in material and workmanship, when they have been installed in accordance with the manufacturer’s instructions, and have not been modified or tampered with. On SE keypad, holes have also been spotted inside the front housing for additional LEDs (LEDs not included).To speed installation of the SE keypad, holes have been spotted on the inside the back housing for mounting to a wall or a single-gang electrical box.For use in extreme weather conditions, consult the factory for additional methods of protecting your keypad.This allows air to circulate and a place for condensation to drain. Do not seal the drain holes at the bottom of the keypad housing.Do not silicone the cover plate because the unit will not seal properly. This helps prevent water from entering the case and condensing on the circuit board. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |